Experimental Study on AA6005-T6 Material Welded with Friction Stir Welding Using Impact Test
View Article
Suplementary File

Supplementary Files

Similarity Check Result

Keywords

Teknik Pengelasan
Friction Stir Welding
Taghuchy
ANNOVA
uji impak

How to Cite

Suprayoga, A., & Mulyadi, M. (2021). Experimental Study on AA6005-T6 Material Welded with Friction Stir Welding Using Impact Test. Indonesian Journal of Innovation Studies, 13, 10.21070/ijins.v13i.532. https://doi.org/10.21070/ijins.v13i.532

Abstract

The welding technique is often the choice in the joining process because of its light weight and relatively simple characteristics. Friction Stir Welding (FSW) is a welding method that was created and developed by The Welding Institute (TWI) in 1991. This easy, fast, and environmentally friendly welding process has been widely applied to construction, especially aluminum materials. The material used in the experiment was AA 6005-T6 6mm thick with varying tool speed parameters 765 1208 1907 3020 (rpm), feed rate 24 43 65 90 (mm/m), engine tilt, pin model (hexagonal, taper square, taper cylinder, cylinder), as well as an incision depth of 0.05 0.1 0.15 0.2 (mm). Using the Taguchy and ANNOVA methods as calculations and data processing. The test carried out is the impact test of the Charpy method using the ASTM E23 standard. After calculating with the Minitab 19 application, it was found that the most influential factor on the impact strength was the engine speed parameter of 765rpm which contributed 28.95%. Keywords: Welding Technique, Friction Stir Welding, Taghuchy, ANNOVA, impact test

https://doi.org/10.21070/ijins.v13i.532
View Article
Suplementary File

References

Angger Sudrajat dan Mahros Darsin. (2012). Analisis Sifat Mekanik Hasil Pengelasan Aluminium Aa 1100 Dengan Metode Friction Stir Welding ( Fsw). Rotor, 5(1), 50–61. https://www.researchgate.net/publication/281628097_ANALISIS_SIFAT_MEKANIK_HASIL_PENGELASAN_ALUMINIUM_AA_1100_DENGAN_METODE_FRICTION_STIR_WELDING_FSW

Asmono, T. B. (2014). Speed Terhadap Kekuatan Tarik Sambungan Las Hasil Friction Stir Welding Pada Aluminium [UNIVERSITAS BRAWIJAYA]. http://repository.ub.ac.id/142738/

Budi Nur Rahman, M., Widyo Nugroho, A., & Satriya Wardhana, B. (2018). Pengaruh Feed Rate dan Kecepatan Putar Pin Tool Friction Stir Welding (FSW) terhadap Kekuatan Tarik dan Kekerasan Aluminium 5052. JMPM (Jurnal Material Dan Proses Manufaktur), 2(2), 83–95. https://doi.org/10.18196/jmpm.2224

Fitrayudha1), A., & Jauhar Fajrin2) & Buan Anshari3). (2020). ANALISIS SIFAT MEKANIS KOMPOSIT POLYESTER SISAL MENGGUNAKAN METODE ANOVA. 14(7), 2817–2824. http://ejurnal.binawakya.or.id/index.php/MBI/article/view/489/pdf

Helmi, I., Balai, T., Logam, B., Bandung, M., & Disetujui, A. (2017). PENGARUH BENTUK PIN TERHADAP SIFAT MEKANIK ALUMINIUM 5083 – H112 HASIL PROSES FRICTION STIR WELDING. RISET TEKNOLOGI INDUSTRI, 11(1), 31–42. http://ejournal.kemenperin.go.id/jrti/article/view/2163

Mochamad Abdul Muftinur1), Haryono2), Johan Wijayanto3), A. P. P. (2017). Analisa Pengaruh Perbedaan Feed Rate Terhadap Kekuatan Tarik Dan Impak Aluminium 6061 Metode Pengelasan Friction Stir Welding. Jurnal Teknik Perkapalan, 5(2), 473–481.

Muhammad Arsyad Suyuti1), A. (2020). SIFAT MEKANIS SAMBUNGAN DISSIMILAR FRICTION STIR WELDING ANTARA ALUMINIUM PADUAN AL-MG DAN AL-MG-SI. SIFAT MEKANIS SAMBUNGAN DISSIMILAR FRICTION STIR WELDING ANTARA ALUMINIUM PADUAN AL-MG DAN AL-MG-SI, 100:98–102. http://jurnal.poliupg.ac.id/index.php/snp2m/article/view/2419

Pratisna, P., Anggertyo, I., A, P. A. N., Induk, L., Labinkimat, M., & Al, T. N. I. (2016). Sifat Fisik dan Mekanik Sambungan Las Friction Stir Welding ( FSW ) AA 5083 dengan Variasi Bentuk dan Kecepatan Putar Probe Pada Konstruksi Kapal Physical and Mechanical Properties of Welded Joints Friction Stir Welding ( FSW ) AA 5083 with a Variation of.

Riyadi, M. R., Jokosisworo, S., & Zakki, A. F. (2019). Pengaruh RPM dan Diameter Pin Tool Terhadap Kekuatan Tarik, Impak, dan Mikrografi Hasil Pengelasan Friction Stir Welding (FSW) Single Side Pada Aluminium 5083. Teknik Perkapalan, 7(4), 494–503.

Riyadi1), M. R., Jokosisworo1), S., & Ahmad Fauzan Zakki). (2019). Pengaruh RPM dan Diameter Pin Tool Terhadap Kekuatan Tarik, Impak, dan Mikrografi Hasil Pengelasan Friction Stir Welding (FSW) Single Side Pada Aluminium 5083. Teknik Perkapalan, 7(4), 168–175. https://ejournal3.undip.ac.id/index.php/naval/article/view/24792

Setyawan, P. E., Irawan, Y. S., & Suprapto, W. (2014). Kekuatan Tarik Dan Porositas Hasil Sambungan Las Gesek Aluminium 6061 Dengan Berbagai Suhu Aging. Rekayasa Mesin, 5(2), pp.141-148. https://doi.org/10.21776/ub.jrm

Siswanto, R., Studi, P., Mesin, T., Teknik, F., & Mangkurat, U. L. (2018). Teknologi pengelasan (hmkb791). TEKNIK PENGELASAN. https://mesin.ulm.ac.id/assets/dist/bahan/Teknologi_Pengelasan_full.pdf

Supplied, Designations, A., & Types, T. (2016). thyssenkrupp Materials ( UK ) Ltd Material Data Sheet Generic Physical Properties. 6–9.

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...